General Discussions

Post new topic   This topic is locked: you cannot edit posts or make replies.

Page 49 of 67 Previous  1 ... 26 ... 48, 49, 50 ... 58 ... 67  Next

View previous topic View next topic Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:40 pm

ons spring maar more in voor ons begin. Ek sal so 10am daar wees.

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Re: General Discussions

Post  vuka on Sat Jul 04, 2009 7:41 pm

MI4 VS TRF???? of 2 races vs 1 000 000 000 000 000 races?????????????????


Last edited by vuka on Sat Jul 04, 2009 7:55 pm; edited 1 time in total

vuka

Posts: 359
Join date: 2009-05-18

View user profile

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:43 pm

ek sal n paar banke moet gaan sien met n shotgun maar die saak is reg. Ek sal jou nie aanvat met n pen stamp session nie, daai trf is hard

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:48 pm

die weerberig vir more lyk heel belowend bounce

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Re: General Discussions

Post  vuka on Sat Jul 04, 2009 7:53 pm

verbasend hard, underground columns is nie eers n match nie Twisted Evil

Jy daai MI4 bietjie laat drift ook. Fusion se die goed vir die bearings, weet nie so mooi nie ek moes met twee ure lank sukkel om hulle weer los te kry gevoel soos die koper buste wat altyd in die karre was

vuka

Posts: 359
Join date: 2009-05-18

View user profile

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:53 pm

no more afrikaans, bra Jay is online Laughing

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

general discussion

Post  ototw on Sat Jul 04, 2009 7:54 pm

penne.trek julle hulle uit en slaan dit weer in deur die swart pyp

ototw

Posts: 1763
Join date: 2008-10-12
Age: 45

View user profile

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:55 pm

drifting maak die bearings lekker los, die stof help nie. As hul skoonmaak voor die tyd kan daar geen skade wees nie.

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:56 pm

ons boor n gaat deur die pyo in lyn met die pen, dan slaan ons hul in. Dit sou beter gewerk het soos jy se maar daai penne sit redelik vas.

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 7:58 pm

check onder video clips die footage van daai klein kameras wat ons verkoop. Dit lyk heel goed van n vliegtuig af, kan nie wag om te sien hoe Fusion se footage by die drifting uitkom nie

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

general discussion

Post  ototw on Sat Jul 04, 2009 7:58 pm

wat slaan jy in ,die pyp rondom die pen

ototw

Posts: 1763
Join date: 2008-10-12
Age: 45

View user profile

Back to top Go down

Re: General Discussions

Post  vuka on Sat Jul 04, 2009 7:59 pm

Raymond wrote:die weerberig vir more lyk heel belowend bounce


Why is it going to rain???

No OTOTw we just drill holes in the pipe and then force them over.

vuka

Posts: 359
Join date: 2009-05-18

View user profile

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 8:00 pm

we drill the hole smaller than the pin and force it over like Vuka is saying. It goes quick, much quicker than the belting

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

general discussion

Post  ototw on Sat Jul 04, 2009 8:01 pm

yes,but how do u force it over,what do u use

ototw

Posts: 1763
Join date: 2008-10-12
Age: 45

View user profile

Back to top Go down

Re: General Discussions

Post  Raymond on Sat Jul 04, 2009 8:01 pm

hands

Raymond

Posts: 2518
Join date: 2008-08-19
Location: Port Elizabeth

View user profile http://www.raymonds-rc-models.co.za

Back to top Go down

Page 49 of 67 Previous  1 ... 26 ... 48, 49, 50 ... 58 ... 67  Next

View previous topic View next topic Back to top


Post new topic   This topic is locked: you cannot edit posts or make replies.
Permissions of this forum:
You cannot reply to topics in this forum